View and Download Lexmark Xe service manual online. Xe All in One Printer pdf manual download. Also for: Xe. View and Download Lexmark Xe service manual online. Xe All in One Printer pdf manual download. Also for: Xe, View and Download Lexmark XE copy manual online. Lexmark XE MFP – Copy guide. XE All in One Printer pdf manual download. Also for: Xe.
|Published (Last):||18 August 2011|
|PDF File Size:||10.47 Mb|
|ePub File Size:||8.76 Mb|
|Price:||Free* [*Free Regsitration Required]|
Lexmark X940e Service Manual
Prints a report of all the fonts available for the printer language currently set in the printer Prints a list of all the resources stored on manuual optional flash memory card or printer hard disk Notes: Page – Sensor registration late jam feeding Page 70 – Sensor bridge unit media exit late jam Page 71 Page 72 – Sensor bridge unit media exit static j Page – X sheet drawer 1TM —sensor tray Remove the bridge unit diverter gate solenoid.
Invalid Pin Touch Continue to clear the message and continue printing. Install the correct toner cartridge Is the correct toner cartridge properly installed? Sides Duplex Use this option to select duplex settings.
Remove the bridge unit hookup cover A. A document can be scanned directly to an FTP site. Collating copies If you print multiple copies of a document, you can choose to print each copy as a set collated or to print the copies as groups of pages not collated.
Was the interconnect card assembly recently replaced? Page – X sheet drawer 1TM —one-way 22 to Requires color calibration adjustments.
Check the four toner cartridges. Page – Switch media size size sensing error Replace the Replace the sensor rear connection. Setting a printer language as the default does not prevent a program from sending print jobs that use another printer language. Does the above component operate properly? Go to step 6.
Lexmark X940E User Manual
Page XXX Assembly Characters have jagged or x940w edges If you are using downloaded fonts, verify that the fonts are supported by the printer, the host computer, and the software program.
Page Page Page – Sensor punch carriage shift hp removal Page – Sensor punch waste box set removal Page – Sensor punch waste box full removal Page – Stapler unit frame removal Page Page – Stapler unit assembly manuql Page Page – Sensor stapler carriage hp removal Page – Media eject unit assembly removal Page Page Page Page – Sub paddle removal Page – Sub paddle drive shaft assembly removal Page Page – Media eject clamp motor assembly removal Page – Sensor media eject clamp hp removal Page – Switch eject cover interlock removal Page – Media compiler unit assembly removal Page Page – Sensor front tamper hp and sensor rea Clearing jams Open the staple cover.
Page – Sensor media level late error tray 1 Page – Switch media size size sensing error Turn the printer back on. Is the chute, located at the lower part of the xx940e component, free of clogs and obstructions? Connector Left Sensor booklet knife folding removal 1. Copying Copying on both sides of the paper duplexing Load an original document faceup, short edge first into the ADF or facedown on lexmarj scanner glass. All other trademarks are the property of their respective owners.
This tube lexmar heated by the inner heater lamp. Page XXX Replacement notes: Press and hold the 2 and 6 buttons simultaneously. Go to Does the error continue?
Check the bridge unit diverter gate solenoid for proper Go to step 6. Type a unique name for the shortcut, and then enter the fax number. Replace the assembly for proper connection. The page prints when this item is selected.
E-mail Server Setup Menu – Lexmark XE User Manual [Page ]
If you need to roll the scanner and its shelf elsewhere, the scanner weighs Counterclockwise rotation of this motor moves the tamper to the rear side. Place the janual cartridge into the upper stapler. Remove the unsupported optional interface card or internal print server from the printer system board.
A4L and A3S are present on the compiler unit assembly, all the sheets are stapled and then ejected to the stacker media bin. Touch ADF pre registration. Release the hook securing the pick roll B to the shaft C. Touch Stacker bin level1. Moisture content The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Remove one screw securing the switch media size A to the manuual inside the machine.
Page – Print irregularities Page – Skewed print Page – Print is too dark Page – Toner fog or background shading appears To order supplies in the U. CMYK toner add motor assembly removal 1.
Solving Scanner Problems The printer is not plugged into any surge protectors, uninterrupted power supplies, or extension cords. Page XXX 6.
Right Connector Sensor booklet media compiler in removal 1.
Learning about the printer Button Button name Back Back Sample screen two Button Button name Down arrow Up arrow Unselected radio button Selected radio button Function When the button is shaped like this, no other navigation is possible from this screen except to go back.